According to recent DIII-D experiments (Logan et al 2024 Nucl. Fusion64 014003), injecting edge localized electron cyclotron current drive (ECCD) in the counter-plasma-current (counter-Ip) direction reduces the n = 3 resonant magnetic perturbation (RMP) current threshold for edge-localized mode (ELM) suppression, while co-Ip ECCD during the suppressed ELM phase causes a back transition to ELMing. This paper presents nonlinear two-fluid simulations on the ECCD manipulation of edge magnetic islands induced by RMP using the TM1 code. In the presence of a magnetic island chain at the pedestal-top, co-Ip ECCD is found to decrease the island width and restore the initially degraded pedestal pressure when its radial deposition location is close to the rational surface of the island. With a sufficiently strong co-Ip ECCD current, the RMP-driven magnetic island can be healed, and the pedestal pressure fully recovers to its initial ELMing state. On the contrary, counter-Ip ECCD is found to increase the island width and further reduce the pedestal pressure to levels significantly below the peeling-ballooning-mode limited height, leading to even stationary ELM suppression. These simulations align with the results from DIII-D experiments. However, when multiple magnetic island chains are present at the pedestal-top, the ECCD current experiences substantial broadening, and its effects on the island width and pedestal pressure become negligible. Further simulations reveal that counter-Ip ECCD enhances RMP penetration by lowering the penetration threshold, with the degree of reduction proportional to the amplitude of ECCD current. For the ∼1 MW ECCD in DIII-D, the predicted decrease in the RMP penetration threshold for ELM suppression is approximately 20%, consistent with experimental observations. These simulations indicate that edge-localized ECCD can be used to either facilitate RMP-driven ELM suppression or optimize the confinement degradation.
ISSN: 1741-4326
Nuclear Fusion is the acknowledged world-leading journal specializing in fusion. The journal covers all aspects of research, theoretical and practical, relevant to controlled thermonuclear fusion.
Open all abstracts, in this tab
Q.M. Hu et al 2024 Nucl. Fusion 64 046027
Sehila M. Gonzalez de Vicente et al 2022 Nucl. Fusion 62 085001
In the absence of official standards and guidelines for nuclear fusion plants, fusion designers adopted, as far as possible, well-established standards for fission-based nuclear power plants (NPPs). This often implies interpretation and/or extrapolation, due to differences in structures, systems and components, materials, safety mitigation systems, risks, etc. This approach could result in the consideration of overconservative measures that might lead to an increase in cost and complexity with limited or negligible improvements. One important topic is the generation of radioactive waste in fusion power plants. Fusion waste is significantly different to fission NPP waste, i.e. the quantity of fusion waste is much larger. However, it mostly comprises low-level waste (LLW) and intermediate level waste (ILW). Notably, the waste does not contain many long-lived isotopes, mainly tritium and other activation isotopes but no-transuranic elements. An important benefit of fusion employing reduced-activation materials is the lower decay heat removal and rapid radioactivity decay overall. The dominant fusion wastes are primarily composed of structural materials, such as different types of steel, including reduced activation ferritic martensitic steels, such as EUROFER97 and F82H, AISI 316L, bainitic, and JK2LB. The relevant long-lived radioisotopes come from alloying elements, such as niobium, molybdenum, nickel, carbon, nitrogen, copper and aluminum and also from uncontrolled impurities (of the same elements, but also, e.g. of potassium and cobalt). After irradiation, these isotopes might preclude disposal in LLW repositories. Fusion power should be able to avoid creating high-level waste, while the volume of fusion ILW and LLW will be significant, both in terms of pure volume and volume per unit of electricity produced. Thus, efforts to recycle and clear are essential to support fusion deployment, reclaim resources (through less ore mining) and minimize the radwaste burden for future generations.
I.A.M. Datta et al 2024 Nucl. Fusion 64 066016
The FuZE sheared-flow-stabilized Z pinch at Zap Energy is simulated using whole-device modeling employing an axisymmetric resistive magnetohydrodynamic formulation implemented within the discontinuous Galerkin WARPXM framework. Simulations show formation of Z pinches with densities of approximately 1022 m−3 and total DD fusion neutron rate of 107 per µs for approximately 2 µs. Simulation-derived synthetic diagnostics show peak currents and voltages within 10% and total yield within approximately 30% of experiment for similar plasma mass. The simulations provide insight into the plasma dynamics in the experiment and enable a predictive capability for exploring design changes on devices built at Zap Energy.
Semin Joung et al 2024 Nucl. Fusion 64 066038
A neural network, BES-ELMnet, predicting a quasi-periodic disruptive eruption of the plasma energy and particles known as edge localized mode (ELM) onset is developed with observed pedestal turbulence from the beam emission spectroscopy system in DIII-D. BES-ELMnet has convolutional and fully-connected layers, taking two-dimensional plasma fluctuations with a temporal window of size 128 µs and generating a scalar output which can be interpreted as a probability of the upcoming ELM onset. As approximately labeled inter-ELM broadband () fluctuations are given to the network, BES-ELMnet learns by itself ELM-related precursors arising before the onsets through supervised learning scheme. BES-ELMnet achieves the gradually increasing ELM onset probabilities between two consecutive ELMs during the inter-ELM phases and can forecast the first ELM onsets which occur after the high confinement mode transition. We further investigate the network generality in terms of the selected frequency band to ensure the use of BES-ELMnet for various operation regimes without changing the trained architecture. Therefore, our novel prediction method will enhance a proactive high confinement mode control of fusion-grade plasmas.
J. Elbez-Uzan et al 2024 Nucl. Fusion 64 037001
The discussion in the international community on how fusion power plants (FPPs) will be licenced and regulated is ongoing. As such, there is a concerted drive from the European stakeholders to understand the requirements from such a framework and how to best establish it with the aim of easing the licensing process of FPPs. Initiated by the EUROfusion consortium, a group of European experts were convened to produce a set of recommendations on the regulatory framework for the safety and licensing of FPPs. To do so effectively, the group assessed lessons learned from existing fusion facilities, reports by International Atomic Energy Agency and European Commission on FPP safety and the on-going work by the UK government, US Nuclear Regulatory Commission and Canadian Nuclear Safety Commission, as well as the licensing process of ITER. As a result, commonalities between fusion and fission were identified in terms of fundamental safety objectives which could facilitate parity in certain framework aspects. However, significant differences to any such implementation were also identified, particularly with respect to the lower hazard potential inherent to FPPs and how to remain proportionate to the associated safety challenges and the physical principles behind these two types of reactors together with their associated technologies. The recognition of the differences in the safety challenges in FPPs and fission-based nuclear power plants (NPPs) is paramount to future regulatory framework development. Ultimately, regulatory frameworks depend upon a country's legal framework, therefore it is apparent that a common global regulatory framework for FPPs is not possible. However, as with present-day NPP regulation, efforts could be made to develop harmonised approaches to FPP regulation to provide common levels of protection. In view of this objective, 12 recommendations are presented across 4 topics: regulations, international databases, codes and standards, safety demonstration rules and regulatory approaches. These recommendations are provided to inform and advise potential future actions on FPP regulatory framework and licencing process principles.
J. Mailloux et al 2022 Nucl. Fusion 62 042026
The JET 2019–2020 scientific and technological programme exploited the results of years of concerted scientific and engineering work, including the ITER-like wall (ILW: Be wall and W divertor) installed in 2010, improved diagnostic capabilities now fully available, a major neutral beam injection upgrade providing record power in 2019–2020, and tested the technical and procedural preparation for safe operation with tritium. Research along three complementary axes yielded a wealth of new results. Firstly, the JET plasma programme delivered scenarios suitable for high fusion power and alpha particle (α) physics in the coming D–T campaign (DTE2), with record sustained neutron rates, as well as plasmas for clarifying the impact of isotope mass on plasma core, edge and plasma-wall interactions, and for ITER pre-fusion power operation. The efficacy of the newly installed shattered pellet injector for mitigating disruption forces and runaway electrons was demonstrated. Secondly, research on the consequences of long-term exposure to JET-ILW plasma was completed, with emphasis on wall damage and fuel retention, and with analyses of wall materials and dust particles that will help validate assumptions and codes for design and operation of ITER and DEMO. Thirdly, the nuclear technology programme aiming to deliver maximum technological return from operations in D, T and D–T benefited from the highest D–D neutron yield in years, securing results for validating radiation transport and activation codes, and nuclear data for ITER.
G. Federici et al 2024 Nucl. Fusion 64 036025
High temperature superconductors (HTSs) offer the promise of operating at higher magnetic field and temperature. Recently, the use of high field magnets (by adopting HTS) has been promoted by several groups around the world, including new start-up entries, both to substantially reduce the size of a fusion power reactor system and as a breakthrough innovation that could dramatically accelerate fusion power deployment. This paper describes the results of an assessment to understand the impact of using high field magnets in the design of DEMO in Europe, considering a comprehensive list of physics and engineering limitations together with the interdependencies with other important parameters. Based on the results, it is concluded that increasing the magnetic field does not lead to a reduction in device size with relevant nuclear performance requirements, because (i) large structures are needed to withstand the enormous electromagnetic forces, (ii) thick blanket and n-shield structures are needed to protect the coils from radiation damage effects, and (iii) new divertor solutions with performances well beyond today's concepts are needed. Stronger structural materials allow for more compact tokamaks, but do not change the conclusion that scalability is not favourable when increasing the magnetic field, beyond a certain point, the machine size cannot be further reduced. More advanced structural support concepts for high-field coils have been explored and concluded that these solutions are either unfeasible or provide only marginal size reduction, by far not sufficient to account for the potential of operating at very high field provided by HTS. Additionally, the cost of high field coils is significant at today's price levels and shows to scale roughly with the square of the field. Nevertheless, it is believed that even when not operated at high field and starting within conventional insulated coils, HTS can still offer certain benefits. These include the simplification of the magnet cooling scheme thanks to increased temperature margin (indirect conduction cooling). This in turn can greatly simplify coil construction and minimize high-voltage risks at the terminals.
P. Rodriguez-Fernandez et al 2022 Nucl. Fusion 62 042003
The SPARC tokamak project, currently in engineering design, aims to achieve breakeven and burning plasma conditions in a compact device, thanks to new developments in high-temperature superconductor technology. With a magnetic field of 12.2 T on axis and 8.7 MA of plasma current, SPARC is predicted to produce 140 MW of fusion power with a plasma gain of Q ≈ 11, providing ample margin with respect to its mission of Q > 2. All tokamak systems are being designed to produce this landmark plasma discharge, thus enabling the study of burning plasma physics and tokamak operations in reactor relevant conditions to pave the way for the design and construction of a compact, high-field fusion power plant. Construction of SPARC is planned to begin by mid-2021.
Vignesh Gopakumar et al 2024 Nucl. Fusion 64 056025
Predicting plasma evolution within a Tokamak reactor is crucial to realizing the goal of sustainable fusion. Capabilities in forecasting the spatio-temporal evolution of plasma rapidly and accurately allow us to quickly iterate over design and control strategies on current Tokamak devices and future reactors. Modelling plasma evolution using numerical solvers is often expensive, consuming many hours on supercomputers, and hence, we need alternative inexpensive surrogate models. We demonstrate accurate predictions of plasma evolution both in simulation and experimental domains using deep learning-based surrogate modelling tools, viz., Fourier neural operators (FNO). We show that FNO has a speedup of six orders of magnitude over traditional solvers in predicting the plasma dynamics simulated from magnetohydrodynamic models, while maintaining a high accuracy (Mean Squared Error in the normalised domain ). Our modified version of the FNO is capable of solving multi-variable Partial Differential Equations, and can capture the dependence among the different variables in a single model. FNOs can also predict plasma evolution on real-world experimental data observed by the cameras positioned within the MAST Tokamak, i.e. cameras looking across the central solenoid and the divertor in the Tokamak. We show that FNOs are able to accurately forecast the evolution of plasma and have the potential to be deployed for real-time monitoring. We also illustrate their capability in forecasting the plasma shape, the locations of interactions of the plasma with the central solenoid and the divertor for the full (available) duration of the plasma shot within MAST. The FNO offers a viable alternative for surrogate modelling as it is quick to train and infer, and requires fewer data points, while being able to do zero-shot super-resolution and getting high-fidelity solutions.
Ting Long et al 2024 Nucl. Fusion 64 064002
We report on comprehensive experimental studies of turbulence spreading in edge plasmas. These studies demonstrate the relation of turbulence spreading and entrainment to intermittent convective density fluctuation events or bursts (i.e. blobs and holes). The non-diffusive character of turbulence spreading is thus elucidated. The turbulence spreading velocity (or mean jet velocity) manifests a linear correlation with the skewness of density fluctuations, and increases with the auto-correlation time of density fluctuations. Turbulence spreading by positive density fluctuations is outward, while spreading by negative density fluctuations is inward. The degree of symmetry breaking between outward propagating blobs and inward propagating holes increases with the amplitude of density fluctuations. Thus, blob-hole asymmetry emerges as crucial to turbulence spreading. These results highlight the important role of intermittent convective events in conveying the spreading of turbulence, and constitute a fundamental challenge to existing diffusive models of spreading.
Open all abstracts, in this tab
M. Sato et al 2024 Nucl. Fusion 64 076021
Effects of the kinetic thermal ions (KTIs) on ideal infernal modes and resistive infernal modes have been investigated by using magnetohydrodynamic (MHD) simulation without KTIs and kinetic-MHD hybrid simulation with KTIs. For the ideal infernal modes, the pressure profile is significantly flattened at the saturated state for both the models with and without the KTIs. As the beta value decreases, the ideal infernal modes are stabilized while the resistive infernal modes are still unstable. For the resistive infernal modes, while the saturated pressure profile is significantly flattened in the MHD simulation without KTIs, the pressure profile is not flattened at the saturated state in the kinetic-MHD hybrid simulation with KTIs. The suppression of the saturation level by the effects of the KTIs results from the phase mismatch between the radial velocity and perturbed pressure mode structures. This indicates that KTIs play an essential role for the suppression of pressure profile flattening due to slowly growing resistive MHD instabilities.
Lan Yin et al 2024 Nucl. Fusion 64 076020
Efficient ion heating is crucial for future fusion devices, and the only way to heat ions directly is ion cyclotron resonance heating. Reported here is a full wave solver integrated with a Fokker–Planck code for optimizing ion heating with ion cyclotron range of frequency waves for the International Thermonuclear Experimental Reactor deuterium–tritium plasma. Both the direct absorption of minority ions and the power transfer to bulk ions via collisions are considered, while also accounting for the edge effects on ion absorption near the core. The simulation results show that the appropriate scrape-off layer density profile and parallel wave number lead to enhanced edge coupling and broaden the absorption region with moderate absorption intensity of the minority ions, which is very important for ion heating. More power from the heated ions is transferred to bulk ions than to electrons through collisions in our simulation via optimization, and reducing the total RF power results in a significant increase of the absorbed fraction of bulk ions.
M. Morbey et al 2024 Nucl. Fusion 64 076019
The vapor-box, a liquid metal design for the divertor, utilizes lithium recirculation through evaporation and condensation. Safety concerns arise from Li-D/T formation and co-deposition on vapor-box walls and the first wall, affecting tritium retention. Additively manufactured tungsten capillary porous structure (CPS) samples with Li were exposed to high heat flux D plasmas in the linear plasma device Magnum-PSI, to study D retention in Li–D co-deposition dependence on substrate temperature (200 C–428 C) and distance from the plasma beam center (25–85 mm). The D:Li ratio was determined via in-situ ion beam diagnostics with simultaneously analyzed Nuclear Reaction Analysis and Elastic Backscattering Spectroscopy spectra to maximize the precision. Experimental results approach close to the theoretical maximum at 40:60 D:Li ratio and deposited film thickness ranging from 0.02 to 3.2 µm. Witness plate temperatures above 400 C yielded Li films under 150 nm in thickness with lower D:Li ratios (5:95 D:Li ratio). At this temperature LiD decomposition pressure is comparable with vessel pressure during plasma. SOLPS-ITER simulations narrowed CPS surface temperature to 650 C–700 C, indicating Li+ plasma dominance near the target surface. Redeposition ratio of lithium on the CPS surface was determined to be around 80, matching quartz crystal microbalance results. However, SOLPS-ITER simulations lacked accuracy in recreating observed Li and D deposition layers on WPs, improvements are needed to model plasmas with significant Li quantities. Extension of SOLPS-ITER simulations to include LiD molecules and enhance heat flux accuracy is crucial for better alignment with experimental data.
M. Rud et al 2024 Nucl. Fusion 64 076018
Tomographic reconstructions of a 3D fast-ion constants-of-motion phase-space distribution function are computed by inverting synthetic signals based on projected velocities of the fast ions along the diagnostic lines of sight. A spectrum of projected velocities is a key element of the spectrum formation in fast-ion D-alpha spectroscopy, collective Thomson scattering, and gamma-ray and neutron emission spectroscopy, and it can hence serve as a proxy for any of these. The fast-ion distribution functions are parameterised by three constants of motion, the kinetic energy, the magnetic moment and the toroidal canonical angular momentum. The reconstructions are computed using both zeroth-order and first-order Tikhonov regularisation expressed in terms of Bayesian inference to allow uncertainty quantification. In addition to this, a discontinuity appears to be present in the solution across the trapped-passing boundary surface in the three-dimensional phase space due to a singularity in the Jacobian of the transformation from position and velocity space to phase space. A method to allow for this apparent discontinuity while simultaneously penalising large gradients in the solution is demonstrated. Finally, we use our new methods to optimise the diagnostic performance of a set of six fans of sightlines by finding where the detectors contribute most complementary diagnostic information for the future COMPASS-Upgrade tokamak.
T. Stoltzfus-Dueck and R. Brzozowski III 2024 Nucl. Fusion 64 076017
Using the assumption of a weak normalized turbulent viscosity, usually valid in practice, the modulated-transport model (Stoltzfus-Dueck 2012 Phys. Plasmas19 055908) is generalized to allow the turbulent transport coefficient to vary in an arbitrary way on radial and poloidal position. The new approach clarifies the physical interpretation of the earlier results and significantly simplifies the calculation, via a boundary-layer asymptotic method. Rigorous detailed appendices verify the result of the simple boundary-layer calculation, also demonstrating that it achieves the claimed order of accuracy and providing a concrete prediction for the strong plasma flows in the immediate vicinity of the last closed flux surface. The new formulas are used to predict plasma rotation at the core-edge boundary, in cases with and without externally applied torque. Dimensional formulas and extensive discussion are provided, to support experimental application of the new model.
Open all abstracts, in this tab
G.D. Conway et al 2022 Nucl. Fusion 62 013001
Geodesic acoustic modes (GAMs) are ubiquitous oscillatory flow phenomena observed in toroidal magnetic confinement fusion plasmas, such as tokamaks and stellarators. They are recognized as the non-stationary branch of the turbulence driven zonal flows which play a critical regulatory role in cross-field turbulent transport. GAMs are supported by the plasma compressibility due to magnetic geodesic curvature—an intrinsic feature of any toroidal confinement device. GAMs impact the plasma confinement via velocity shearing of turbulent eddies, modulation of transport, and by providing additional routes for energy dissipation. GAMs can also be driven by energetic particles (so-called EGAMs) or even pumped by a variety of other mechanisms, both internal and external to the plasma, opening-up possibilities for plasma diagnosis and turbulence control. In recent years there have been major advances in all areas of GAM research: measurements, theory, and numerical simulations. This review assesses the status of these developments and the progress made towards a unified understanding of the GAM behaviour and its role in plasma confinement. The review begins with tutorial-like reviews of the basic concepts and theory, followed by a series of topic orientated sections covering different aspects of the GAM. The approach adopted here is to present and contrast experimental observations alongside the predictions from theory and numerical simulations. The review concludes with a comprehensive summary of the field, highlighting outstanding issues and prospects for future developments.
L. Marrelli et al 2021 Nucl. Fusion 61 023001
This paper reviews the research on the reversed field pinch (RFP) in the last three decades. Substantial experimental and theoretical progress and transformational changes have been achieved since the last review (Bodin 1990 Nucl. Fusion 30 1717–37). The experiments have been performed in devices with different sizes and capabilities. The largest are RFX-mod in Padova (Italy) and MST in Madison (USA). The experimental community includes also EXTRAP-T2R in Sweden, RELAX in Japan and KTX in China. Impressive improvements in the performance are the result of exploration of two lines: the high current operation (up to 2 MA) with the spontaneous occurrence of helical equilibria with good magnetic flux surfaces and the active control of the current profile. A crucial ingredient for the advancements obtained in the experiments has been the development of state-of-art active feedback control systems allowing the control of MHD instabilities in presence of a thin shell. The balance between achievements and still open issues leads us to the conclusion that the RFP can be a valuable and diverse contributor in the quest for fusion electricity.
Mohamed Abdou et al 2021 Nucl. Fusion 61 013001
The tritium aspects of the DT fuel cycle embody some of the most challenging feasibility and attractiveness issues in the development of fusion systems. The review and analyses in this paper provide important information to understand and quantify these challenges and to define the phase space of plasma physics and fusion technology parameters and features that must guide a serious R&D in the world fusion program. We focus in particular on components, issues and R&D necessary to satisfy three 'principal requirements': (1) achieving tritium self-sufficiency within the fusion system, (2) providing a tritium inventory for the initial start-up of a fusion facility, and (3) managing the safety and biological hazards of tritium. A primary conclusion is that the physics and technology state-of-the-art will not enable DEMO and future power plants to satisfy these principal requirements. We quantify goals and define specific areas and ideas for physics and technology R&D to meet these requirements. A powerful fuel cycle dynamics model was developed to calculate time-dependent tritium inventories and flow rates in all parts and components of the fuel cycle for different ranges of parameters and physics and technology conditions. Dynamics modeling analyses show that the key parameters affecting tritium inventories, tritium start-up inventory, and tritium self-sufficiency are the tritium burn fraction in the plasma (fb), fueling efficiency (ηf), processing time of plasma exhaust in the inner fuel cycle (tp), reactor availability factor (AF), reserve time (tr) which determines the reserve tritium inventory needed in the storage system in order to keep the plant operational for time tr in case of any malfunction of any part of the tritium processing system, and the doubling time (td). Results show that ηffb > 2% and processing time of 1–4 h are required to achieve tritium self-sufficiency with reasonable confidence. For ηffb = 2% and processing time of 4 h, the tritium start-up inventory required for a 3 GW fusion reactor is ∼11 kg, while it is <5 kg if ηffb = 5% and the processing time is 1 h. To achieve these stringent requirements, a serious R&D program in physics and technology is necessary. The EU-DEMO direct internal recycling concept that carries fuel directly from the plasma exhaust gas to the fueling systems without going through the isotope separation system reduces the overall processing time and tritium inventories and has positive effects on the required tritium breeding ratio (TBRR). A significant finding is the strong dependence of tritium self-sufficiency on the reactor availability factor. Simulations show that tritium self-sufficiency is: impossible if AF < 10% for any ηffb, possible if AF > 30% and 1% ⩽ ηffb ⩽ 2%, and achievable with reasonable confidence if AF > 50% and ηffb > 2%. These results are of particular concern in light of the low availability factor predicted for the near-term plasma-based experimental facilities (e.g. FNSF, VNS, CTF), and can have repercussions on tritium economy in DEMO reactors as well, unless significant advancements in RAMI are made. There is a linear dependency between the tritium start-up inventory and the fusion power. The required tritium start-up inventory for a fusion facility of 100 MW fusion power is as small as 1 kg. Since fusion power plants will have large powers for better economics, it is important to maintain a 'reserve' tritium inventory in the tritium storage system to continue to fuel the plasma and avoid plant shutdown in case of malfunctions of some parts of the tritium processing lines. But our results show that a reserve time as short as 24 h leads to unacceptable reserve and start-up inventory requirements. Therefore, high reliability and fast maintainability of all components in the fuel cycle are necessary in order to avoid the need for storing reserve tritium inventory sufficient for continued fusion facility operation for more than a few hours. The physics aspects of plasma fueling, tritium burn fraction, and particle and power exhaust are highly interrelated and complex, and predictions for DEMO and power reactors are highly uncertain because of lack of experiments with burning plasma. Fueling by pellet injection on the high field side of tokamak has evolved to be the preferred method to fuel a burning plasma. Extrapolation from the DIII-D penetration scaling shows fueling efficiency expected in DEMO to be <25%, but such extrapolations are highly uncertain. The fueling efficiency of gas in a reactor relevant regime is expected to be extremely poor and not very useful for getting tritium into the core plasma efficiently. Gas fueling will nonetheless be useful for feedback control of the divertor operating parameters. Extensive modeling has been carried out to predict burn fraction, fueling requirements, and fueling efficiency for ITER, DEMO, and beyond. The fueling rate required to operate Q = 10 ITER plasmas in order to provide the required core fueling, helium exhaust and radiative divertor plasma conditions for acceptable divertor power loads was calculated. If this fueling is performed with a 50–50 DT mix, the tritium burn fraction in ITER would be ∼0.36%, which is too low to satisfy the self-sufficiency conditions derived from the dynamics modeling for fusion reactors. Extrapolation to DEMO using this approach would also yield similarly low burn fraction. Extensive analysis presented shows that specific features of edge neutral dynamics in ITER and fusion reactors, which are different from present experiments, open possibilities for optimization of tritium fueling and thus to improve the burn fraction. Using only tritium in pellet fueling of the plasma core, and only deuterium for edge density, divertor power load and ELM control results in significant increase of the burn fraction to 1.8–3.6%. These estimates are performed with physics models whose results cannot be fully validated for ITER and DEMO plasma conditions since these cannot be achieved in present tokamak experiments. Thus, several uncertainties remain regarding particle transport and scenario requirements in ITER and DEMO. The safety standard requirements for protection of the public and release guidelines for tritium have been reviewed. General safety approaches including minimizing tritium inventories, reducing tritium permeation through materials, and decontaminating material for waste disposal have been suggested.
Boris N. Breizman et al 2019 Nucl. Fusion 59 083001
Of all electrons, runaway electrons have long been recognized in the fusion community as a distinctive population. They now attract special attention as a part of ITER mission considerations. This review covers basic physics ingredients of the runaway phenomenon and the ongoing efforts (experimental and theoretical) aimed at runaway electron (RE) taming in the next generation tokamaks. We emphasize the prevailing physics themes of the last 20 years: the hot-tail mechanism of runaway production, RE interaction with impurity ions, the role of synchrotron radiation in runaway kinetics, RE transport in presence of magnetic fluctuations, micro-instabilities driven by REs in magnetized plasmas, and vertical stability of the plasma with REs. The review also discusses implications of the runaway phenomenon for ITER and the current strategy of RE mitigation.
M.K.A. Thumm et al 2019 Nucl. Fusion 59 073001
In many tokamak and stellarator experiments around the globe that are investigating energy production via controlled thermonuclear fusion, electron cyclotron heating and current drive (ECH&CD) are used for plasma start-up, heating, non-inductive current drive and magnetohydrodynamic stability control. ECH will be the first auxiliary heating method used on ITER. Megawatt-class, continuous wave gyrotrons are employed as high-power millimeter (mm)-wave sources. The present review reports on the worldwide state-of-the-art of high-power gyrotrons. Their successful development during recent years changed ECH from a minor to a major heating method. After a general introduction of the various functions of ECH&CD in fusion physics, especially for ITER, section 2 will explain the fast-wave gyrotron interaction principle. Section 3 discusses innovations on the components of modern long-pulse fusion gyrotrons (magnetron injection electron gun, beam tunnel, cavity, quasi-optical output coupler, synthetic diamond output window, single-stage depressed collector) and auxiliary components (superconducting magnets, gyrotron diagnostics, high-power calorimetric dummy loads). Section 4 deals with present megawatt-class gyrotrons for ITER, W7-X, LHD, EAST, KSTAR and JT-60SA, and also includes tubes for moderate pulse length machines such as ASDEX-U, DIII-D, HL-2A, TCV, QUEST and GAMMA-10. In section 5 the development of future advanced fusion gyrotrons is discussed. These are tubes with higher frequencies for DEMO, multi-frequency (multi-purpose) gyrotrons, stepwise frequency tunable tubes for plasma stabilization, injection-locked and coaxial-cavity multi-megawatt gyrotrons, as well as sub-THz gyrotrons for collective Thomson scattering. Efficiency enhancement via multi-stage depressed collectors, fast oscillation recovery methods and reliability, availability, maintainability and inspectability will be discussed at the end of this section.
Open all abstracts, in this tab
Cruz-Zabala et al
Impurity profiles have been measured with the edge high field side
(HFS) and low field side (LFS) charge exchange recombination spectroscopy
suite at ASDEX Upgrade enabling the study of the poloidal structure of the
edge parallel flow in H-mode, L-mode and I-mode. In H-mode, asymmetries
in the impurity density, toroidal and poloidal rotations are found. In I-mode,
only toroidal rotation asymmetries have been measured while in L-mode no
asymmetries have been observed. The measured parallel flow can be divided in two
components, the Pfirsch-Schlüter (PS) flow and the symmetric flow. Two different
methods have been followed to determine both contributions to the parallel flow.
The first method is based on the calculation of the PS flow at the HFS and LFS
from the radial electric field. The second method directly provides the symmetric
flow from the flux surface average of the parallel flow. In H-mode, the methods
provide different results, while in L-mode and I-mode they agree. The differences
observed in H-mode between the two methods could be explained by the existence
of asymmetries in the impurity density, by the non-negligible particle sources and
radial losses, or by the approximations made in the calculation of the flux surface
average of the parallel flow from measurements in two poloidal positions (midplane
HFS and LFS) only.
Meng et al
The spatio-temporal evolution of the energetic particles in the transport time scale in tokamak plasmas is a key issue of the plasmas confinement, especially in burning plasmas. In order to include sources and sinks and collisional slowing down processes, a new solver, ATEP-3D was implemented to simulate the evolution of the EP distribution in the three-dimensional constants of motion (CoM) space. The Fokker-Planck collision operator represented in the CoM space is derived and numerically calculated. The collision coefficients are averaged over the unperturbed orbits to capture the fundamental properties of EPs. ATEP-3D is fully embedded in ITER IMAS framework and combined with the LIGKA/HAGIS codes. The finite volume method and the implicit Crank-Nicholson scheme are adopted due to their optimal numerical properties for transport time scale studies. ATEP-3D allows the analysis of the particle and power balance with the source and sink during the transport process to evaluate the EP confinement properties.
Shankar et al
We present an improved model for the study of edge biasing in a tokamak plasma that incorporates electron and ion mobility contributions. The non-ambipolar nature of the drifts due to the electron/ion mobility terms influences the space charge separation due to edge biasing and affects plasma dynamics in the edge and SOL regions in a significant manner. In contrast to earlier studies, the present model enables simulation studies at higher biasing voltages. The inclusion of mobility enhances/decreases the effect of negative/positive biasing. The radial profiles of plasma density, electron temperature, radial electric field, and its shear for positive as well as negative biasing are investigated as a function of mobility.
Arena et al
In the framework of the activities coordinated by the EUROfusion consortium, the Water thermal-HYDRAulic (W-HYDRA) experimental platform is being built at the ENEA Brasimone Research Centre in order to support the development of the Water-Cooled Lead Lithium (WCLL) Breeding Blanket (BB). In particular, this infrastructure will make possible the installation and testing of prototypical mock-ups under relevant working conditions, such as the First Wall (FW), the manifold and the Steam Generator (SG). Moreover, it will represent an integral test facility for the investigation of phenomena characteristic of WCLL BB concept, such as the PbLi/water interaction. Finally, the collection of data coming from the different planned experimental campaigns will allow to qualify and validate numerical models and codes currently adopted for the design of components, as well as for the modelling of complex phenomena typical of the WCLL BB.
In order to come to a definitive design of the different facilities constituting the experimental platform, several design analyses assessing the thermal, hydraulic and structural performances of the different facilities and components are necessary. The paper reports a highlight of the W-HYDRA platform with a general description of the facilities. Some of the most relevant design studies carried out so far are reported as well, highlighting their impact on the evolution of the design.
Bandaru et al
The vertical motion and shrinking of the cold plasma column after a tokamak disruption leads to a natural decrease in the edge safety factor when all the current is carried by runaway electrons. Reaching a low edge safety factor can potentially cause a strong plasma instability. We present magnetohydrodynamic simulations of the termination of a post-disruption plateau-phase runaway electron beam in ITER when the edge safety factor falls close to two. Growth of instabilities is observed to result in stochastization of the magnetic field and a prompt loss of runaway electrons. Higher background plasma resistivity is seen to cause larger mode magnitudes and stronger stochastization, leading to less remnant runaway electrons after the termination event. Lower ion-densities also project a qualitatively similar behaviour although weaker in effect. Using computations from a wall collision model, the ensuing load distribution on the first-wall is also presented.
Open all abstracts, in this tab
M. Sato et al 2024 Nucl. Fusion 64 076021
Effects of the kinetic thermal ions (KTIs) on ideal infernal modes and resistive infernal modes have been investigated by using magnetohydrodynamic (MHD) simulation without KTIs and kinetic-MHD hybrid simulation with KTIs. For the ideal infernal modes, the pressure profile is significantly flattened at the saturated state for both the models with and without the KTIs. As the beta value decreases, the ideal infernal modes are stabilized while the resistive infernal modes are still unstable. For the resistive infernal modes, while the saturated pressure profile is significantly flattened in the MHD simulation without KTIs, the pressure profile is not flattened at the saturated state in the kinetic-MHD hybrid simulation with KTIs. The suppression of the saturation level by the effects of the KTIs results from the phase mismatch between the radial velocity and perturbed pressure mode structures. This indicates that KTIs play an essential role for the suppression of pressure profile flattening due to slowly growing resistive MHD instabilities.
Lan Yin et al 2024 Nucl. Fusion 64 076020
Efficient ion heating is crucial for future fusion devices, and the only way to heat ions directly is ion cyclotron resonance heating. Reported here is a full wave solver integrated with a Fokker–Planck code for optimizing ion heating with ion cyclotron range of frequency waves for the International Thermonuclear Experimental Reactor deuterium–tritium plasma. Both the direct absorption of minority ions and the power transfer to bulk ions via collisions are considered, while also accounting for the edge effects on ion absorption near the core. The simulation results show that the appropriate scrape-off layer density profile and parallel wave number lead to enhanced edge coupling and broaden the absorption region with moderate absorption intensity of the minority ions, which is very important for ion heating. More power from the heated ions is transferred to bulk ions than to electrons through collisions in our simulation via optimization, and reducing the total RF power results in a significant increase of the absorbed fraction of bulk ions.
Diego Jose Cruz-Zabala et al 2024 Nucl. Fusion
Impurity profiles have been measured with the edge high field side
(HFS) and low field side (LFS) charge exchange recombination spectroscopy
suite at ASDEX Upgrade enabling the study of the poloidal structure of the
edge parallel flow in H-mode, L-mode and I-mode. In H-mode, asymmetries
in the impurity density, toroidal and poloidal rotations are found. In I-mode,
only toroidal rotation asymmetries have been measured while in L-mode no
asymmetries have been observed. The measured parallel flow can be divided in two
components, the Pfirsch-Schlüter (PS) flow and the symmetric flow. Two different
methods have been followed to determine both contributions to the parallel flow.
The first method is based on the calculation of the PS flow at the HFS and LFS
from the radial electric field. The second method directly provides the symmetric
flow from the flux surface average of the parallel flow. In H-mode, the methods
provide different results, while in L-mode and I-mode they agree. The differences
observed in H-mode between the two methods could be explained by the existence
of asymmetries in the impurity density, by the non-negligible particle sources and
radial losses, or by the approximations made in the calculation of the flux surface
average of the parallel flow from measurements in two poloidal positions (midplane
HFS and LFS) only.
Guo Meng et al 2024 Nucl. Fusion
The spatio-temporal evolution of the energetic particles in the transport time scale in tokamak plasmas is a key issue of the plasmas confinement, especially in burning plasmas. In order to include sources and sinks and collisional slowing down processes, a new solver, ATEP-3D was implemented to simulate the evolution of the EP distribution in the three-dimensional constants of motion (CoM) space. The Fokker-Planck collision operator represented in the CoM space is derived and numerically calculated. The collision coefficients are averaged over the unperturbed orbits to capture the fundamental properties of EPs. ATEP-3D is fully embedded in ITER IMAS framework and combined with the LIGKA/HAGIS codes. The finite volume method and the implicit Crank-Nicholson scheme are adopted due to their optimal numerical properties for transport time scale studies. ATEP-3D allows the analysis of the particle and power balance with the source and sink during the transport process to evaluate the EP confinement properties.
M. Morbey et al 2024 Nucl. Fusion 64 076019
The vapor-box, a liquid metal design for the divertor, utilizes lithium recirculation through evaporation and condensation. Safety concerns arise from Li-D/T formation and co-deposition on vapor-box walls and the first wall, affecting tritium retention. Additively manufactured tungsten capillary porous structure (CPS) samples with Li were exposed to high heat flux D plasmas in the linear plasma device Magnum-PSI, to study D retention in Li–D co-deposition dependence on substrate temperature (200 C–428 C) and distance from the plasma beam center (25–85 mm). The D:Li ratio was determined via in-situ ion beam diagnostics with simultaneously analyzed Nuclear Reaction Analysis and Elastic Backscattering Spectroscopy spectra to maximize the precision. Experimental results approach close to the theoretical maximum at 40:60 D:Li ratio and deposited film thickness ranging from 0.02 to 3.2 µm. Witness plate temperatures above 400 C yielded Li films under 150 nm in thickness with lower D:Li ratios (5:95 D:Li ratio). At this temperature LiD decomposition pressure is comparable with vessel pressure during plasma. SOLPS-ITER simulations narrowed CPS surface temperature to 650 C–700 C, indicating Li+ plasma dominance near the target surface. Redeposition ratio of lithium on the CPS surface was determined to be around 80, matching quartz crystal microbalance results. However, SOLPS-ITER simulations lacked accuracy in recreating observed Li and D deposition layers on WPs, improvements are needed to model plasmas with significant Li quantities. Extension of SOLPS-ITER simulations to include LiD molecules and enhance heat flux accuracy is crucial for better alignment with experimental data.
M. Rud et al 2024 Nucl. Fusion 64 076018
Tomographic reconstructions of a 3D fast-ion constants-of-motion phase-space distribution function are computed by inverting synthetic signals based on projected velocities of the fast ions along the diagnostic lines of sight. A spectrum of projected velocities is a key element of the spectrum formation in fast-ion D-alpha spectroscopy, collective Thomson scattering, and gamma-ray and neutron emission spectroscopy, and it can hence serve as a proxy for any of these. The fast-ion distribution functions are parameterised by three constants of motion, the kinetic energy, the magnetic moment and the toroidal canonical angular momentum. The reconstructions are computed using both zeroth-order and first-order Tikhonov regularisation expressed in terms of Bayesian inference to allow uncertainty quantification. In addition to this, a discontinuity appears to be present in the solution across the trapped-passing boundary surface in the three-dimensional phase space due to a singularity in the Jacobian of the transformation from position and velocity space to phase space. A method to allow for this apparent discontinuity while simultaneously penalising large gradients in the solution is demonstrated. Finally, we use our new methods to optimise the diagnostic performance of a set of six fans of sightlines by finding where the detectors contribute most complementary diagnostic information for the future COMPASS-Upgrade tokamak.
Vijay Shankar et al 2024 Nucl. Fusion
We present an improved model for the study of edge biasing in a tokamak plasma that incorporates electron and ion mobility contributions. The non-ambipolar nature of the drifts due to the electron/ion mobility terms influences the space charge separation due to edge biasing and affects plasma dynamics in the edge and SOL regions in a significant manner. In contrast to earlier studies, the present model enables simulation studies at higher biasing voltages. The inclusion of mobility enhances/decreases the effect of negative/positive biasing. The radial profiles of plasma density, electron temperature, radial electric field, and its shear for positive as well as negative biasing are investigated as a function of mobility.
Pietro Arena et al 2024 Nucl. Fusion
In the framework of the activities coordinated by the EUROfusion consortium, the Water thermal-HYDRAulic (W-HYDRA) experimental platform is being built at the ENEA Brasimone Research Centre in order to support the development of the Water-Cooled Lead Lithium (WCLL) Breeding Blanket (BB). In particular, this infrastructure will make possible the installation and testing of prototypical mock-ups under relevant working conditions, such as the First Wall (FW), the manifold and the Steam Generator (SG). Moreover, it will represent an integral test facility for the investigation of phenomena characteristic of WCLL BB concept, such as the PbLi/water interaction. Finally, the collection of data coming from the different planned experimental campaigns will allow to qualify and validate numerical models and codes currently adopted for the design of components, as well as for the modelling of complex phenomena typical of the WCLL BB.
In order to come to a definitive design of the different facilities constituting the experimental platform, several design analyses assessing the thermal, hydraulic and structural performances of the different facilities and components are necessary. The paper reports a highlight of the W-HYDRA platform with a general description of the facilities. Some of the most relevant design studies carried out so far are reported as well, highlighting their impact on the evolution of the design.
Vinodh Kumar Bandaru et al 2024 Nucl. Fusion
The vertical motion and shrinking of the cold plasma column after a tokamak disruption leads to a natural decrease in the edge safety factor when all the current is carried by runaway electrons. Reaching a low edge safety factor can potentially cause a strong plasma instability. We present magnetohydrodynamic simulations of the termination of a post-disruption plateau-phase runaway electron beam in ITER when the edge safety factor falls close to two. Growth of instabilities is observed to result in stochastization of the magnetic field and a prompt loss of runaway electrons. Higher background plasma resistivity is seen to cause larger mode magnitudes and stronger stochastization, leading to less remnant runaway electrons after the termination event. Lower ion-densities also project a qualitatively similar behaviour although weaker in effect. Using computations from a wall collision model, the ensuing load distribution on the first-wall is also presented.
T. Stoltzfus-Dueck and R. Brzozowski III 2024 Nucl. Fusion 64 076017
Using the assumption of a weak normalized turbulent viscosity, usually valid in practice, the modulated-transport model (Stoltzfus-Dueck 2012 Phys. Plasmas19 055908) is generalized to allow the turbulent transport coefficient to vary in an arbitrary way on radial and poloidal position. The new approach clarifies the physical interpretation of the earlier results and significantly simplifies the calculation, via a boundary-layer asymptotic method. Rigorous detailed appendices verify the result of the simple boundary-layer calculation, also demonstrating that it achieves the claimed order of accuracy and providing a concrete prediction for the strong plasma flows in the immediate vicinity of the last closed flux surface. The new formulas are used to predict plasma rotation at the core-edge boundary, in cases with and without externally applied torque. Dimensional formulas and extensive discussion are provided, to support experimental application of the new model.